Installing Cork Flooring

Installing cork flooring is easy, whether you are installing cork tiles or panels. Carefully read about cork flooring installing guidelines with each manufacturer you consider to catch the subtleties that may exist.

There may be issues around installing cork floors in bathrooms, on radiant floors, and in dry climates. Installing cork flooring tiles requires glue while installing floating cork flooring doesn’t so that the floor can move freely — float — across the floor with expansion and contraction.

The natural characteristics of cork means that when installing cork flooring, the variations in shade and pattern that make cork so unique and beautiful must be taken into account. Cork tiles should be shuffled prior to installation to ensure a more evenly balanced coloring on the floor.

Report this ad

The tendency of cork to expand and contract with humidity changes can be minimized by installing floating cork flooring, and by stabilizing the temperature and humidity in your house. Even so, installing cork floors in bathrooms or other areas with high moisture content should be avoided. However, if your choose to install cork flooring in a bathroom, the perimeter of the room should be caulked prior to installing the baseboards to avoid moisture penetration (or you can calk around the baseboards for the same reason).


To further minimize the impact of variables in the climate, the cork flooring must acclimate for 3-4 days prior to installation. To do this, simply remove the cork tile from its packaging and leave in the room where the floor will be installed. The room temperature should be between 60F and 70F with normal levels of humidity. If you live in a particularly dry climate, let the cork acclimate for several weeks to make sure it has dried and contracted as much as it’s likely to so that you don’t get shrinkage once it’s installed.

Installation Process For Cork Flooring


Prepare the Subfloor

Generally, cork can be installed over any sub-floor as long as it is smooth, level, clean, and dry. That means that any old paint, wax, grease, polish, and old adhesive must be removed to ensure a good bond.

  • For installation over existing wood floors, scrub with tri-sodium phosphate after using a paint or varnish remover. In extreme cases, the floor should be sanded, and then washed, rinsed, and allowed to dry.
  • For concrete sub-flooring, make sure the concrete is level using a latex fill or leveler. Then the cement should be primed using a concreted primer or for higher-moisture rooms, covered with polyethylene sheets as a moisture barrier.
  • To install on existing vinyl or other smooth surfaces, ensure the old floor is in good condition and rough up the smooth surface to ensure a good adhesive bond.
  • Cork floors do not seem to adversely affect radiant-heat systems as long as a “vapor barrier” is laid down between the sub-floor and the cork. However, check with the manufacturer to ensure compatibility and for recommendations for maintenance.
Report this ad
Lay the Tile

Once the sub-floor is ready, layout your cork tiles, making sure that the color and pattern variations are scattered throughout your room. Before applying your water-based contact cement adhesive to the perimeter of the room using a paint brush, chalk your lines onto the sub-floor. Then, using a paint roller to apply the adhesive to the rest of the floor, paint directly over the chalk lines because the adhesive will dry clear. Allow to completely dry for about an hour until tacky before laying the cork tile.


Starting in one corner, align the first tile to the chalk line and the next tile tight to the edge of the first. The remaining tiles can be laid in the same fashion and if necessary, can be cut using a sharp utility or linoleum knife. To attain a positive contact between the tile and sub-floor, the tiles must be hit with a mallet or rolled with a standard tile roller four times in each direction.

Finishing

Before applying a top coat of urethane or flooring wax to your tiled floor, remove any excess adhesive from the floor using a damp cloth, if the adhesive is wet, and mineral spirits if the adhesive is dry. Plus, the tiles and seams should be vacuumed and then cleaned with a sponge. Since many of the cork tiles already have finish on them when sold, this final top coat helps protect the adhesive from moisture working its way through the seams.


If you opt to install a floating floor, be sure to leave a 1/4-1/2 inch gap around the edges of the room, giving room for expansion when temperatures and humidity rise. Some cork floor companies expect you to put an expansion joint at each room change, not just at doorways; be sure to ask before you make your cork purchase what your cork floor company’s policy is. Another interesting note is that you see maximum lengths of how much floating cork you lay before inserting an expansion joint; generally that number is much lower than is really necessary.

The video below shows a step-by-step process for cork floor installation.


Let the finish dry for four hours before walking on the floor with socks and 24 hours before walking on the floor with shoes. Your installation is complete.

If you’re looking for an ecologically friendly flooring option that fits within your budget, cork flooring may be the ideal solution for you! Cork floor is a hardy and sensible flooring option that is easy to maintain and a beautiful alternative to traditional hardwoods.

The earthy style cork flooring brings to a room creates a cozy ambiance and this comfortable flooring option is quickly becoming a favorite in kitchens, living rooms and basements.

These days, manufacturers have designed cork flooring planks similar to laminate flooring, with a tongue and groove type design, eliminating the need for glue or nails. This makes installing cork flooring a fairly simple process that can be accomplished in a reasonable amount of time by even a novice DIY-er.

Prior To Installation, Gather The Following Tools

  • Straightedge and clamps
  • A saw suitable to cut the cork flooring: a jigsaw, handsaw, table saw or circular saw can work.
  • Rubber hammer or rubber mallet
  • Crowbar
  • Miter box ad drill/driver to cut and install shoe molding
  • 1/2″ wooden spacers

The floating floor design of cork flooring panels, where the planks are not required to be glued or nailed onto a subfloor, has truly simplified the installation process.

It is recommended that you install a plywood subfloor and/or moisture barrier if the floors are being installed in a potentially damp area. Otherwise, the cork flooring can be laid directly on preexisting vinyl, linoleum, hardwood, or concrete floors. Cork flooring should never be installed directly on top of carpet, however.

Because cork flooring will expand and contract with changes in humidity, you must leave a ½” gap between the flooring and the wall or there will be damage to your floors as they expand.

Of course, you are not going to want to leave this gap exposed, as that would be extremely unsightly, so you will need to cover the gaps with baseboard or shoe molding. If there is already existing shoe molding in the room where you are installing your cork flooring, it will need to be removed before installing the new floor.

If you would like to reuse the molding, take care not to crack it when removing and it can be placed over the expansion gap after the cork floors have been laid.

Additionally, you will want to acclimatize your cork flooring to the room prior to installation. Most manufacturers recommend leaving your flooring unwrapped from any plastic covering for a minimum of 72 hours in the room where it will be installed to allow the planks to adjust to the atmosphere and humidity levels in the room.

The room should be at least 60 degrees while the floors are being acclimatized. The subfloor or preexisting flooring on which the cork flooring is to be installed should also be made clear of dust and debris of any sort.

Finally, after gathering the above tools, leaving your cork flooring to adjust to the room for at least 72 hours, removing any existing baseboards or shoe molding, and cleaning the area on which the cork flooring is to be laid, you are ready to begin. You will want to set aside approximately 3 hours per 100 square foot space you have to work with.

Cork Flooring Installation

  1. If you are installing any kind of moisture barrier, such as a polyurethane sheeting, you will want to install that at this point. Run the sheeting up the wall about 2-3 inches, to help keep out moisture.
  2. Measure the length of the room and trim the cork flooring planks to fit; remember to leave the ½” space on either end for expansion.
  3. Begin the initial installation of the first row of cork flooring planks. To lay the cork flooring, push the planks together at an angle so the one end of the board slides into the corresponding groove on the subsequent plank until the boards click together. The pieces should be installed short end to short end and worked lengthwise like this (not long side to long side). You may need the force of your rubber mallet to join the boards, but do not hammer on the edges of the planks where the tongue and groove have been brought together; rather, hammer in the middle of the boards to prevent cracking.
  4. As you reach the end of the row, cut the last piece to length, using your saw guided by a clamped straightedge.
  5. As you lay the flooring, to save the ½ inch for expansion, place ½-inch wood spacers between the long end of the first row of cork floor planks and the wall. Line up this initial row of flooring boards tight against the spacers.
  6. Continue installation of the rest of the cork flooring boards, using the rubber mallet to ensure each row of planks are installed tightly against one another.
  7. As you install the final row, trim the planks to allow for the ½” expansion between the edge of the flooring and the wall.

Now that the flooring has been laid, most manufacturers recommend applying an additional polyurethane layer to protect the porous nature of the cork flooring from possible water damage.

Prior to applying the polyurethane, vacuum floors to remove any dust and dirt to ensure a complete and even application.

Let the finish dry for at least 24 hours before walking on the floor at all, and for the majority of the polyurethane finishes, a final hardness is achieved after 8 days, at which point you can install the shoe molding.

Measure the shoe molding and cut to length (if using a new molding and not re-installing preexisting shoe molding you removed prior to installation).

Join the molding at the corners of the room at a 45-degree angle and do not nail the molding directly to the cork flooring. Rather, nail the molding into the baseboard at 12-inch intervals.

At this point, you can rejoice! You have completed your cork flooring installation and your new floors are ready to be enjoyed.

Report this ad

67 thoughts on “Installing Cork Flooring”

  1. I think the glue would ultimately pull the paint from the wood, as you are surmising too. That would indeed leave your choice being the floating floors. How much space are you putting into cork? I’m asking because of expansion joint issues.
    Whatever you do be sure to acclimate the cork for a long time before installing it. And if at all possible, be sure to seal it so you get better durability with the finish.

    Reply
  2. My new floating cork floor looks dull after a light wash. Can I still apply a water based polyurethane? Also, yikes! I see a (new)slight “split” or creasing, not a gap of any kind though where two of my planks were snapped together. If I stand there it disappears – what can I do to perm. fix?
    Thank you!

    Reply
  3. Hi Dianna,
    For the moment, I wouldn’t do anything to the floor, but I would recommend that you get the salesman and flooring company there immediately and start getting the manufacturer to honor their warranty. It does sound like you have a defective floor.
    Your flooring wasn’t made by “Natural Cork” flooring was it? If so, you may want to read this horror story about a new cork floor.
    If you’d like to talk directly, let me know – I’ll be glad to email you my phone number.

    Reply
  4. Dianna, I had floating cork floors installed in my new home several years ago and we had separations between tiles. Is your floor buckling at the panel joints? How long did you acclimate the flooring panels before installation? And how did you acclimate them?

    Reply
  5. Hi there, I have a further question about installing cork tiles on stairs. I am trying to avoid using a capping or timber bull nose on our stairecase. I have been told that I could install the cork tiles and lightly sand the meeting point between the cork tread and cork riser so that the tread slightly ‘rolls over’ (like a bull nose i guess). What do you think? Would this be practical?

    Reply
  6. Tim, I didn’t have a bullnose for my cork-floor stairs and loved the look. The way my builder approached the finish was to create a wood edge that the step and riser cork butted against. We applied 4-5 coats of Varathane Diamond Coat Polyurethane before installing it and it held nicely.
    Use a hard wood so it will hold up against the wear and tear stairs get. Alder is the wood we used for our cabinets so we used that for the stairs too. It was a beautiful combination, nice enough the sales rep took a picture to share with not only the company but also other clients.
    If you haven’t heard me say before (you really aught to read the entire thread here, if you haven’t) let me repeat myself. :~) Be very careful about the source of your cork, let at acclimate for weeks or months before applying it to your floors, and coat even prefinished cork with the previously mentioned polyurethane.
    Enjoy.

    Reply
  7. i purchased from ifloors . com… he said no poly…..it will void the warrenty… tiger natural planks floating floor. uv coated acrylic finish by WESTHALLOW.

    Reply
  8. Hi Phil,
    You need to look over your warranty – if you don’t have one you need to get one. Have you gone to a search engine to find the manufacturers website? I would recommend calling them and asking – “he” may not know what he’s talking about.

    Reply
  9. i read the 20 year warranty. i picked up 10 cases of the STATE COLLECTION BY WESTHOLLOW@CORK TIGER NATURAL. IT IS STATED ON THE PAGES WRAPED IN THE BOXES……… non factory applied finishes (by owner or installer) in cluding but not limited to refinishing or caoting will void warrenty… these planks are uv factory acrylic finished…

    Reply
  10. i will be installing them this week .. i picked up the rug last night….today i am laying down plywood to bring it up to the same height as my tiled kitchen.. i will lert you know how it goes….. is there a way to post pictures on this site??

    Reply
  11. Wondering about cork on stairs….concerned about how to finish it ans well as the durability and slipperiness? Can you send/post any photos of cork stairs?

    Reply
  12. Hi Phillip,
    Even though you never actually ‘asked’ a question, I’m presuming that you want to put poly on it. Now that you’ve read the box, obviously this will void your warranty which isn’t a good thing. It’s up to you if you want to risk voiding your warranty, I’m sure not going to tell you to.

    Reply
  13. Hi Deb,
    Cork on stairs work fine, especially with a bullnose edging to protect the corners. I would suggest using google.com to look for photos of cork flooring on stairs as I don’t have any photos myself.

    Reply
  14. Hi, Wondering about installing the glue down cork under the toilet. Some say I need to put toilet on a marble base and run cork to that. Others say put toilet on cork same as vinyl and toilet may need to be retightened once as it settles?

    Reply
  15. Hi, we were wondering about installing a cork floor over either the slab or the existing vinyl sheet flooring over concrete slab–which would be better? Also, will we need to remove the cabinets since we aren’t replacing those? Or can we just take up the quarter round around the cabinets, install the cork and then replace the quarter round trim?
    Thanks for your advice!

    Reply
  16. What are some solutions for finishing the outside edge when laying cork around a brick fireplace and a sliding glass door, when you account for the expansion. Thanks for the help.

    Reply
  17. Hi Lor,
    How are you planning to install the cork flooring – glueing it down or floating it? Either way will work whether or not you remove the vinyl. You can use the trim as well if you aren’t removing the cabinets. Keep in mind too that with the new height difference it could interfere with opening doors, etc. You might want to take out the old vinyl if you think this may be a problem – it’ll help give you a little more wiggle room.

    Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.